Saturday, June 21, 2008

Mounting Lace on a Barrette

Some questions in the tatting lists recently prompted me to show you how I attach my tatted lace to a barrette. The first thing to do is cover up the ugly metal bar. This method takes a little time, but it not only covers the bar it gives you a base to attach your tatting to. You will need ribbon like gross grain ribbon about a half inch wide either to match your tatting or in a neutral colour, a sewing needle and invisible nylon thread.

In this instance I have a white tatted flower and my ribbon is white so I can begin by using ordinary white thread. Open the barrette and remove the centre spring by bending it a little and pulling it out first on one side, then on the other. Put it aside while you work on the bar.
Measure off a length of ribbon about 2.5 times the length of the bar. In this case it's about 8 inches. You need to have more than enough to go completely around the bar. Notice that this ribbon happens to have a pattern of white dots on it. Don't worry about tone on tone pattern as it won't really be noticeable when you're done.
Insert the ribbon under the clasp and pull it about half way down the inside of the barrette as shown here. Wrap the other end around the barrette and insert it under the hinge at the opposite end of the barrette like this. Fold the end about a half inch so that the cut end is folded under
and begin to stitch the end down making sure that it is wrapped snugly around the bar. Shiny metal and shiny white ribbon don't photograph well,

but you can see the fold and the beginnings of the first stitch.

Work across the centre seam to the edge of the ribbon and whip stitch along the edge just catching the outer edge of the ribbon on both the top and the bottom as shown below.
When you reach the end slide the needle under the ribbon and out the other side and continue whip stitching down the second side of the barrette. Here is the completed bar with the ribbon sewn down both sides.

Take the spring and insert it in on the hinge side with the arch facing away from the barrette. Bend it a little to get it under the clasp side. Now the barrette is wrapped in ribbon and ready for attaching the tatting.

If sewing isn't something you want to do you can attach the ribbon by using a glue gun, just make sure that you don't get any glue on the top side of the barrette where it might show. Glue down the first side, then fold under the second end and make sure the ribbon is tight before you apply the glue.

This pattern has green leaves as well as a white flower and white thread is going to very noticeable on the dark green The invisible nylon thread works with any colour of thread and it's invisible when its on.

Tie a knot in the end of the thread and slip the needle under the ribbon on the top side of the bar bring the needle out in the middle on the ribbon close to one end go through the tatting and the middle of one end and then insert the needle under the ribbon again and take a stitch. Work along the bar taking a stitch in the ribbon and a stitch in the lace.

Add in the second leaf and continue tacking it down all along the length of the bar, as shown here. You may not be using leaves and flowers, but the process is the same.

The last piece to be added is the white flower. Stitch through the middle of the flower and and into the ribbon tacking it in several places. Tie a knot in the thread feed the needle through the ribbon out through the side and cut.

Sometimes, depending on what it is I am attaching, I just leave long ends on the tatting and wrap them around the ribbon covered barrette and literally tie the lace onto the barrette criss crossing the thread around the bar and back through the tatting. This method, although not quite as secure, has the bonus of not having to hide the thread ends.

Again, if sewing's not your thing, you can use a hot glue gun, but you take the risk of damaging your lace. If that isn't a concern then go ahead and glue it.

5 comments:

Unknown said...

What a great pictorial. I'm saving a link on this one.Woo Hoo!!! Good one, Sharon!

LadyShuttleMaker aka MadMadPotter said...

Sharon, you have been awarded AND tagged. Please see my blog for details. :)

Debbie S. said...

Oh, thank you Sharon....
This was just perfect timing... I have finished some little 'bits' of tatting that I want to put on a hair clip for my little neice... she runs over to look at my tatting basket to see what color I am using... so I know she would love to wear a bit of tatting!!!
AND I also want to say THANK YOU for the updates on the 25 motif challenge blog.... Of course, I want to read EVERYONE's blog, but your summing-up makes me want to stay on the computer.. 'for just one more blog'! :)

zarina said...

THANK YOU. Now I can persuade my niece to tie her hair - either using the scrunchies or this. Putting this link in my site so I can easily refer to it wherever I am.

Eileene said...

sharon, you have saved my sanity!! My mail carrier wanted one for her 3 year old daughter the has very fine hair. Thank you xoxoxoxoxo A big ole smouch (thats a kiss in southern) Eileene aka noiseynana